Description

Mogami cable — Made in Japan.

Neutrik connector — Made in Liechtenstein.

Canare 3.5 mm TS connectors — Made in Japan.

Assembled in Tokyo.

Delivered from the other side of the planet — no extra charges for US buyers (DDP).

┉┉┉┉┉┉┉┉┉┉┉┉┉┉┉┉┉┉┉

Your DAW can control complex Eurorack and CV-compatible synth systems. With Ableton Push 3 and the right breakout cable, the connection can be surprisingly simple.

This professional TRS-to-dual-TS breakout cable is designed for routing two separate CV signals from one 1/4” TRS pedal/CV port on Ableton Push 3 to two independent 3.5 mm TS plugs.

The Tip and Ring of the 1/4” TRS plug are separated into two individual 3.5 mm TS outputs, allowing two independent signals to be sent directly to modular, semi-modular, and other CV-compatible synthesizer gear.

This cable may also be used as a stereo breakout, dual-mono breakout, or insert-style breakout cable when your equipment is specifically designed to carry two separate unbalanced signals on a TRS jack.

Please note: this is a breakout cable, not a mono splitter cable, not a passive summing cable, not a headphone splitter, and not a balanced TRS audio cable.

 

No signal conversion, voltage scaling, buffering, or protection circuitry is included. Please confirm that your equipment supports TRS-to-dual-TS breakout wiring before use.

===============================

SELECT YOUR OPTIONS ABOVE:

• Cable Part:

– Mogami 2893

Miniature quad cable, approx. Ø4.8 mm per cable leg.

Recommended when you prefer a sturdier, more substantial cable.

– Mogami 2944

Miniature two-conductor shielded cable, approx. Ø2.5 mm per cable leg.

Recommended when you prefer a slimmer, lighter, more flexible cable.

• Connector Combination:

– NEUTRIK NP3X-B 1/4″ TRS → dual CANARE F11 3.5 mm TS male plugs

 

• Length:

– 2 ft

– 3.28 ft (1 m)

– 4 ft

– 5 ft

– 6 ft

– 10 ft (3 m)

– 15 ft

– 16.5 ft (5 m)

– 23 ft (7 m)

– 30 ft

 

• Quantity:

– 1 breakout cable per order unit

 

Length Note:

Length is measured from the 1/4″ TRS plug to each 3.5 mm TS plug.

This cable has two separate cable legs from the TRS side to the two 3.5 mm TS plugs.

The split section is managed with a simple hook-and-loop cable tie, so the two cable legs can be adjusted or arranged according to your setup.

===============================

 

Professional CV / TRS Breakout Cable:

• Built for Ableton Push 3 pedal-port CV output to external modular or CV-compatible gear.

• 1/4″ TRS plug breaks out into two independent 3.5 mm TS male plugs.

• Useful for sending two CV signals from one Push 3 pedal port.

• With two breakout cables, up to four CV signals can be routed from Push 3.

• NEUTRIK NP3X-B 1/4″ TRS connector for the Push / TRS side.

• CANARE F11 3.5 mm TS male connectors for the modular / synth side.

• Mogami cable options available:

– Mogami 2893 for a sturdier miniature quad construction.

– Mogami 2944 for a slimmer and more flexible miniature shielded construction.

• The two 3.5 mm TS plugs are marked according to the TRS side: Tip and Ring.

 

===============================

Compatibility / Important Notes

 

This cable is a passive breakout cable. It separates the Tip and Ring of a 1/4″ TRS plug into two separate 3.5 mm TS male plugs.

 

Wiring:

Tip → 3.5 mm TS plug 1 tip

Ring → 3.5 mm TS plug 2 tip

Sleeve → common ground

 

According to publicly available Ableton documentation, Push 3 CV output from the pedal jacks operates in the 0–10V range and supports positive voltage values. This means that Push 3 may not directly cover bipolar voltage ranges such as -5V to +5V without additional processing, offset, attenuation, or appropriate configuration.

 

To use Push 3 for CV output, your Push / Ableton Live / DAW setup must be configured correctly. This may include enabling the pedal ports as CV outputs, using compatible CV Tools devices, selecting the correct routing, and setting the receiving CV instrument appropriately, such as unipolar mode when required.

 

Please make sure that your Ableton Live version, Live edition, Push 3 firmware, and Push operating mode support the CV output function you intend to use.

 

The receiving modular, semi-modular, or CV-capable device must also be configured correctly. Depending on the connected equipment, voltage range, input type, calibration, routing, grounding, and user settings, proper operation cannot be guaranteed in every individual setup.

 

This cable guarantees only the physical wiring / pin assignment described above. It does not guarantee that every Push 3, DAW, CV Tools, Eurorack, semi-modular, or external hardware setup will function as expected.

 

This cable may also be used as a TRS-to-dual-TS breakout cable for compatible audio, insert-style, stereo breakout, or dual-mono applications where the pin assignment is appropriate.

However, this is not a mono splitter cable. It does not duplicate one mono signal into two identical outputs.

This cable is not a headphone splitter, not a balanced TRS audio cable, and not a stereo-to-mono summing cable.

Do not use this cable to combine two outputs into one mono input. Combining outputs without a proper summing circuit may damage equipment or cause improper operation.

Please check the manuals of your devices before connecting. If you are unsure whether this cable is suitable for your setup, please contact me before purchasing.

===============================

Trademark / Affiliation Notice:

Ableton and Push are trademarks or registered trademarks of their respective owners.

This product is not made by Ableton, is not an official Ableton accessory, and is not endorsed by or affiliated with Ableton.

The names Ableton and Push 3 are used only to describe the intended compatibility and application of this cable.

===============================

Craftsmanship:

• Handcrafted in Tokyo, Japan with new Mogami cable, Neutrik connector, and Canare connectors.

• Professionally soldered using USA-made 63/37 alloy solder at 360°C (680°F) with a Japanese industrial station.

• Built for stable signal transfer, mechanical reliability, and long-term studio use.

• Each cable is tested after assembly and again before shipment.

 

Bulk Orders & Professional Supply

We specialize in strategic sourcing and have a deep understanding of the technical demands and logistical challenges musicians and audio professionals face when it comes to cables.

Our goal is to simplify the process and deliver the exact cables you need — quickly and reliably.

 

• Bulk Quantities: Orders of 10, 20, or more cables can often be shipped within 1 business day if in stock.

• Lead Time for Non-Stock Items: Typically 1–7 business days.

• FedEx Option: Where available, bulk orders benefit from volume shipping discounts. For large quantities, FedEx is usually the most economical choice — and all import duties and taxes are prepaid by us.

 

Warranty & Notes:

• Handmade — minor cosmetic variations may occur but never affect performance.

• This is a TRS-to-dual-TS passive breakout cable. It is not a balanced TRS audio cable.

• This product is not made by Ableton and is not an official Ableton accessory.

• If you have any concerns or special requests, message us anytime.

 

Included Sticker:

This product comes with a randomly selected sticker.

The sticker has no special meaning.

You may place it anywhere you like, or use it on the connector to indicate cable traceability, depending on your preference.

 

==================================

“NEKODEN” TOKYO JPN

Neko Densen AUDIO CABLES

Handcrafted Professional Cabling

Precision Soldering – Japan Made