Mogami 2931 4-Channel XLR Snake Cable Neutrik Gold 3-164 ft – Assembled in Tokyo

Description

MOGAMI 2931 four-channel balanced analog snake cable with genuine Neutrik XLR connectors.

Made with new components and individually assembled and tested in Tokyo.

Built for practical setup and routing, with quick channel identification, selectable fan-out lengths, and reinforced breakout sections.

 

==================================

SELECT YOUR OPTIONS ABOVE

• Cable length: 3–164 ft (approximately 0.9–50 m)

• Fan-out length: Select from the available options

• Connector configuration: 4 × XLR female to 4 × XLR male

• Cable color: Black

• Quantity: 1 four-channel snake cable assembly

==================================

CHANNEL IDENTIFICATION

Every channel is clearly identified at both ends by both color and number.

• CH 1 — Brown (Neutrik XXR1)

• CH 2 — Red (Neutrik XXR2)

• CH 3 — Orange (Neutrik XXR3)

• CH 4 — Yellow (Neutrik XXR4)

The color sequence follows the original channel color coding used inside the MOGAMI 2931 cable.

A clearly printed channel number is also placed near every connector.

In addition, MOGAMI’s original channel number remains visible through the clear reinforcing sleeve.

This gives each channel three visible identification cues:

 

• Neutrik color ring

• Printed channel label near the connector

• Original MOGAMI core marking

This makes patching, tracing, and troubleshooting easier, especially behind racks or around dense stage wiring.

 

==================================

REINFORCED FAN-OUT CONSTRUCTION

Each individual fan-out lead is covered along its entire length with clear 3:1 adhesive-lined dual-wall heat-shrink tubing. This provides additional mechanical protection while keeping the original MOGAMI channel-number markings clearly visible.

Both main breakout points are reinforced with two nested layers of the same 3:1 adhesive-lined dual-wall heat-shrink tubing.

A reusable hook-and-loop cable tie is fitted near each breakout. It can be repositioned to control where the four leads separate and helps distribute pulling forces across the bundle rather than concentrating them at the reinforced breakout.

Fan-out length can be selected from the available options above.

 

==================================

 

CABLE

• MOGAMI 2931 four-channel multicore microphone cable

• Four individually twisted and shielded balanced pairs

• 26 AWG conductors with XLPE insulation

• Dedicated drain wire and served bare-copper shield for each channel

• Flexible black outer jacket

• Approximate overall diameter: 8.6 mm / 0.339 in

• Made in Japan

==================================

CONNECTORS

• 4 × genuine Neutrik NC3FXX-B female XLR connectors

• 4 × genuine Neutrik NC3MXX-B male XLR connectors

• Black metal housings

• Gold-plated contacts

• Genuine Neutrik XXR1–XXR4 color coding rings

• 8 XLR connectors in total

==================================

WIRING AND TESTING

• Standard balanced XLR wiring

• Pin 1 to Pin 1

• Pin 2 to Pin 2

• Pin 3 to Pin 3

• Each channel is individually checked for correct channel assignment, continuity, and shorts before shipment

Suitable for balanced analog microphone and line-level connections, including recording studios, live sound systems, stage racks, mixers, audio interfaces, microphone preamps, analog outboard equipment, and patching systems.

 

==================================

 

LENGTH

The selected cable length is the approximate finished length measured from connector end to connector end.

The fan-out sections are included within the selected overall cable length.

The selected fan-out length applies to both ends of the cable.

 

▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞▚▞

NekoDensen Assembled in Tokyo Japan